Quick answer: When a PC turns on but shows no display, the fault is usually outside the computer or easy to reach: the wrong monitor input, the cable in the motherboard port instead of the graphics card, or a RAM stick that has worked loose. Check those first. If the board fails its self-test or the graphics card is dead, it needs the workshop. No display diagnosis and repair from $50, diagnosis free when you go ahead. Updated November 2026.
See Repair Service →WhatsApp 9131 8317This guide is for one specific situation: the PC does get power. Fans spin, the case lights glow, maybe the keyboard lights up, but the monitor stays black or says “No signal”. If nothing happens at all when you press the button, that is a different fault, and our PC won’t turn on guide covers it.
The good news is that a black screen with a running PC is often fixable at home. Work through the steps below in order. Each one rules out a cause before you move to the next, more involved one.
Step 1: Rule out the monitor, cable and input
Start with the parts you can check without a screwdriver.
- Is the monitor on and on the right input? Most monitors have two or three inputs (HDMI 1, HDMI 2, DisplayPort). Press the input or source button and cycle through them. A monitor set to HDMI 2 will say “No signal” forever while your PC is happily running on DisplayPort.
- Swap the cable. HDMI and DisplayPort cables do fail, especially cheap ones that get bent behind a desk. Try a known good cable.
- Try another screen. Plug the PC into a TV or a second monitor. If that works, the PC is fine and the monitor is the problem.
- Remove adapters. DisplayPort to HDMI or VGA adapters are a common source of blank screens. Test with a direct cable if you can.
Step 2: Check which port the cable is plugged into
This is the single most common cause we see at the counter. If your desktop has a separate graphics card, the display cable must go into the ports on that card, which sit lower down on the back of the case in a horizontal row. The ports higher up, next to the USB sockets, belong to the motherboard.
When a graphics card is installed, most motherboards switch off their own video output. Plug into the motherboard port and you get a black screen even though everything works. It happens a lot after someone moves house, cleans the desk, or buys a used PC from Carousell and plugs it in for the first time.
Step 3: Reseat the RAM
If the cable is in the right place and you still have no picture, the next suspect is memory. A RAM stick that has lifted slightly in its slot will stop the PC from completing its startup checks, so it never sends a picture to the screen.
- Shut down, switch off at the wall and unplug the power cable.
- Press the power button once to drain leftover charge.
- Open the side panel, release the clips on each RAM slot and pull the sticks out.
- Push each stick back in firmly until both clips snap shut.
- If you have two sticks, try booting with just one, then the other, to find a faulty stick or slot.
Touch the metal case before handling parts to discharge static. In Singapore’s humidity, also check for green or white corrosion on the gold contacts. A gentle wipe with a clean eraser can help.
Step 4: Read the beep codes and debug LEDs
Every PC runs a self-test called POST (power-on self-test) before it shows anything on screen. If POST fails, the screen stays black. The PC usually tells you where it got stuck, if you know where to look.
Beep codes. If your case has a small speaker connected to the motherboard, listen at startup. One short beep normally means POST passed. Repeating or long beeps point to a fault. The exact pattern depends on the BIOS maker, so look up your motherboard model’s manual. Many newer boards have no speaker, so silence does not mean everything is fine.
Debug LEDs. Most motherboards from the last several years have four small LEDs near the RAM slots labelled CPU, DRAM, VGA and BOOT. During startup they light up one after another. If one stays lit, that is where the problem is:
- DRAM stuck on: RAM problem. Go back to Step 3.
- VGA stuck on: graphics card or its power cable. See Step 5.
- CPU stuck on: processor, CPU power cable or motherboard.
- BOOT stuck on: the PC passed POST but cannot find a drive to boot from. You should usually still see a BIOS screen.
Some higher-end boards show a two-digit code instead. The manual lists what each code means.
| Symptom | Most likely cause | DIY fix? | Typical outcome |
|---|---|---|---|
| “No signal” message on monitor | Wrong input, bad cable or wrong port | Yes | Usually a $0 fix |
| Fans spin, black screen, DRAM LED on | Loose or faulty RAM | Yes, reseat | Often a $0 fix |
| VGA LED on or video beep pattern | Graphics card or its power cable | Check cables | Workshop if cables are fine |
| Black screen after a BIOS change or overclock | Bad BIOS settings | Yes, CMOS reset | Usually fixed at home |
| CPU LED on, no beeps | CPU, power cable or motherboard | No | Workshop diagnosis |
| Logo shows, then black once Windows loads | Graphics driver or display settings | Yes, Safe Mode | Software fix |
Step 5: Suspect the graphics card
If the VGA light stays on, or your beep pattern points to video, look at the graphics card.
- Check the power cables. Most mid-range and higher cards need one or more 6+2 pin or 16-pin cables from the power supply. A half-seated connector is enough to stop the card from working.
- Reseat the card. Unscrew it, press the slot latch, pull it out and push it back in firmly.
- Test without it. If your processor has built-in graphics, remove the card and plug the monitor into the motherboard port. A picture now means the card is the likely culprit.
Graphics cards that worked for years and suddenly give no display often have a failed component, a cracked solder joint, or damage from heat. If you saw glitches or crashes in the weeks before, read our guide to the signs a graphics card is dying. We test and fix cards through our graphics card repair service from $60.
Step 6: Reset the CMOS
If the black screen started right after you changed BIOS settings, turned on a memory profile (XMP or EXPO), overclocked, or swapped the processor, clearing the BIOS settings often brings the picture back.
The settings are kept alive by a small coin battery on the motherboard, the CMOS battery. To reset: unplug the PC, then either short the CLR_CMOS pins with a screwdriver as the manual shows, press the clear CMOS button if your board has one, or remove the coin battery for five minutes and put it back. The first boot after a reset can take longer than usual while memory is retrained, so give it a minute before deciding it failed.
When the picture appears, then disappears
If you see the maker’s logo or the BIOS screen, but the display goes black once Windows starts loading, the hardware is mostly fine. The cause is usually a graphics driver, a refresh rate the monitor cannot handle, or Windows sending the picture to a different screen. Boot into Safe Mode (interrupt startup three times to reach recovery options), uninstall the graphics driver, then install a fresh one from NVIDIA, AMD or Intel.
When to stop and bring it in
Stop DIY if the CPU light stays on, if you smell burning, if you see damage on the graphics card or board, or if nothing changes after the steps above. A bench test with known good parts finds the fault quickly, and you avoid buying parts you do not need.
Our Bugis shop is a short walk from the Civic District. If you are around there, see our page for computer repair City Hall for directions and what to bring.
FAQ
The most common causes are the monitor on the wrong input, the cable in the motherboard port instead of the graphics card, or loose RAM. Less often it is a failed graphics card, bad BIOS settings or a motherboard fault.
Yes. If the RAM is loose or faulty, the PC cannot finish its power-on self-test, so it never sends a picture to the monitor. Reseating the sticks or testing them one at a time fixes many of these cases.
Check whether the VGA debug LED stays lit on the motherboard. If your processor has built-in graphics, remove the card and plug the monitor into the motherboard port. If you now get a picture, the card or its power cable is the likely fault.
It often does if the problem started after a BIOS change, memory profile or overclock. Resetting CMOS returns the BIOS to default settings and does not delete your files.
It means the monitor is on but receiving nothing on the input it is set to. Check the input setting, the cable and which port the cable is plugged into before assuming the PC is faulty.
At our shops, no display diagnosis and repair starts from $50, and graphics card repair and testing from $60. Diagnosis is free when you go ahead with the repair, and parts are quoted before any work.
More questions? See our common PC questions.
Still a black screen? WhatsApp us what you see: which lights stay on, any beeps, and whether the monitor says “No signal”. We will tell you if it is worth the trip. Or bring it to Bugis Street #CFL A08, open daily 11am–8pm, or Parkway Parade #B1-45, open daily 11am–9pm.
Repairs from $50 →WhatsApp UsFurther reading: PC won’t turn on: troubleshooting guide · Signs your graphics card is dying · Why a PC randomly restarts
Quick Diagnosis
Plug into the graphics card, not the motherboard
Read the CPU / DRAM / VGA / BOOT LEDs
RAM, GPU and board testing
No fix, no feeFrom $50